AKA Mr. Cold Boot

Part Category: Cables

  • R640 10 Bay BP Signal Cable

    R640 10 Bay BP Signal Cable

    Signal cable that connects the backplane to the motherboard on the Dell PowerEdge R640 10 Bay server.

    Notes:

    • Dell PowerEdge R640 10-SFF
    • Backplane signal cable
    • Connects the system board to the backplane expander
    • Connects MB_SIG_1 on the motherboard to EXP on the expander
    • 1 × 16-pin connector to 1 × 16-pin connector
    • Approximately 43 cm long
    • Used with the 10 × 2.5-inch SFF drive configuration
    • Dell P/N: 059G4K
    • Alternate P/N: 59G4K
    • Not to be confused with the R640 backplane power cables; this is a signal/data cable.

     

  • R730 8 Bay SFF BP Power Cable 0123W8

    R730 8 Bay SFF BP Power Cable 0123W8

    This is the power cable that attaches from the backplane to the motherboard on a Dell Poweredge R730 8 Bay SFF server.

    Notes

    • 8-pin backplane power cable assembly.
    • Approximately 9 inches (23 cm) in length.
    • Power cable only; it does not carry SAS/SATA data or backplane control signals. Those functions are handled by separate RAID and signal cables.
    • Typically used alongside the RAID cable (such as 0F037K) and a separate backplane signal cable (such as 0TRFPV, depending on the server configuration).
    • Dell DP/N: 0123W8 (alternate part number 123W8).

     

  • R730 8 Bay SFF BP Signal Cable 0TRFPV

    R730 8 Bay SFF BP Signal Cable 0TRFPV

    This is the signal cable that attaches from the backplane to the motherboard on a Dell PowerEdge R730 8 Bay SFF server.

    Notes

    • 16-pin to 16-pin signal cable.
    • Approximately 23.5 inches (60 cm) in length.
    • Used to carry control/status signals between the motherboard and the drive backplane; it is not a SAS data cable.
    • Commonly used in Dell PowerEdge R730 systems.
    • Also found in some PowerEdge R730xd and Precision Tower 7910 configurations.
    • Dell DP/N: 0TRFPV (alternate part number TRFPV).
  • R730 8 Bay SFF Mini Mono Cable 0F037K

    R730 8 Bay SFF Mini Mono Cable 0F037K

    This is the SAS storage cable for the R730 8 Bay SFF server. One end connects to the backplane and the other end routes through the right side channel of the server where it terminates at one of Dells mini mono RAID or HBA controllers.

    Notes:

    • Dual Mini-SAS HD (SFF-8643) cable assembly.
    • Used with Dell PERC Mini controllers including H330 Mini, H730 Mini, and H730P Mini.
    • Commonly found in Dell PowerEdge R730 and R730xd systems with front SAS/SATA backplanes.
    • Connects the RAID controller directly to the front drive backplane, carrying data for up to eight front drives on standard 8-bay configurations.
    • Uses SFF-8643 (Mini-SAS HD) connectors on both ends.
    • Dell DP/N: 0F037K (also written as F037K).
  • Cisco UCS C220 M5 internal SAS RAID controller cable

    Cisco UCS C220 M5 internal SAS RAID controller cable

    This is the SAS storage cable found in the Cisco UCS C220 M5 server. It is attached to the backplane and then routes along the right side of the server where it terminates at a RAID controller located in the mRAID riser.

    Notes:

    • Genuine Cisco OEM internal SAS cable assembly.
    • Used in the Cisco UCS C220 M5 Rack Server storage subsystem.
    • Provides the connection between the RAID controller (such as Cisco modular RAID controller / mRAID configurations or supported PCIe RAID adapters) and the internal SAS/SATA drive backplane.
    • Cable assembly uses Mini-SAS HD connectors for high-density SAS connectivity.
    • Supports SAS/SATA drive communication for internal storage configurations.
    • Designed with Cisco-specific cable length and routing to fit the C220 M5 chassis airflow layout.
    • Required for configurations using hardware RAID controllers and SAS backplanes.
    • Proper cable routing is important to avoid interference with fans and airflow paths in the 1U chassis.
    • OEM cable ensures correct connector keying, impedance, and signal integrity.
    • Commonly missing from refurbished or decommissioned servers when RAID components are removed.
    • Cable only; does not include RAID controller, riser, backplane, or drive cage unless otherwise specified.