AKA Mr. Cold Boot

Part Category: Cables

  • R740xd Mid Bay Power Cable 03CH4K

    R740xd Mid Bay Power Cable 03CH4K

    This is the power cable that attaches from the R740xd mid bay backplane to the motherboard.

    Notes:

    • Internal power cable used with the Dell PowerEdge R740/R740xd.
    • Designed to provide power to the 4 × 3.5-inch mid-chassis drive backplane.
    • Used as part of the R740xd mid-tray storage configuration.
    • Connects the mid-drive backplane to the server’s power distribution/motherboard power connection.
    • Dell P/N: 03CH4K (3CH4K).
    • Configuration-specific; not required on R740/R740xd systems without the mid-chassis 4 × 3.5-inch drive module.
  • R530 8 Bay LFF PERC Cable

    R530 8 Bay LFF PERC Cable

    This is the primary SAS storage cable for the Dell PowerEdge R530. It connects the backplane to a Dell compatible mini mono RAID controller.

    Notes

    • Connects the PERC controller to both SAS ports on the 8-drive backplane.
    • Uses two SFF-8087 Mini-SAS connectors at the backplane end.
    • Approximately 21.5 inches (0.55 m) long.
    • Intended for the R530 8 × 3.5-inch LFF configuration.
    • 0JCJNY and JCJNY are the same Dell part number, with the leading zero omitted in some listings.
  • R530 8 Bay LFF MB Signal Cable

    R530 8 Bay LFF MB Signal Cable

    This is the signal cable for the Dell PowerEdge R530 8 Bay LFF server. It connects the backplane to the motherboard.

    Notes

    • The 0PD7P8 is a 16-pin backplane signal cable used to connect the motherboard to the storage backplane.
    • It is documented for both the PowerEdge R520 and R530, including the 8-drive configurations.
    • The cable is approximately 12.5 inches (0.32 m) long.
    • 0PD7P8 and PD7P8 are the same Dell part number, with the leading zero omitted in many listings.
    • This is a signal/I²C cable, not the primary SAS data cable connecting the RAID controller to the drives. It carries communication between the system board and backplane.
    • The R530 uses this cable as part of the 8-bay backplane connection.
  • R530 Control Panel Cable

    R530 Control Panel Cable

    This is the front control panel cable for the Dell PowerEdge R530. It connects the front control panel to the motherboard.

    Notes:

    • Connects the front control panel to the system motherboard on Dell PowerEdge R520/R530 servers.
    • Used with the R520/R530 front control panel assembly.
    • 0VCXFV and VCXFV are the same Dell part number, with the leading zero omitted in some listings.
    • On R530 systems, it is used with the 0CDVG8 front control panel and 00FTN6 front USB cable in configurations equipped with the VGA/USB front panel.
    • This is a signal/control cable, not a power cable.
  • R640 10 Bay BP Signal Cable

    R640 10 Bay BP Signal Cable

    Signal cable that connects the backplane to the motherboard on the Dell PowerEdge R640 10 Bay server.

    Notes:

    • Dell PowerEdge R640 10-SFF
    • Backplane signal cable
    • Connects the system board to the backplane expander
    • Connects MB_SIG_1 on the motherboard to EXP on the expander
    • 1 × 16-pin connector to 1 × 16-pin connector
    • Approximately 43 cm long
    • Used with the 10 × 2.5-inch SFF drive configuration
    • Dell P/N: 059G4K
    • Alternate P/N: 59G4K
    • Not to be confused with the R640 backplane power cables; this is a signal/data cable.