AKA Mr. Cold Boot

Manufacturer: HPE

  • HP DL 360 G10 10 Bay NVME Riser 869514-001

    HP DL 360 G10 10 Bay NVME Riser 869514-001

    This is an NVME riser. It enables NVME support on the HP DL 360 G10 10 Bay server. NVME cables connect from the backplane and then feed into this riser.

    Notes:

    • Secondary NVMe riser board; not a storage controller.
    • Used with the 875556-001 10SFF Premium SAS/SATA/NVMe backplane for NVMe drive support.
    • Requires the appropriate NVMe cables between the riser and the backplane.
    • Provides PCIe connectivity required for direct NVMe drive attachment.
    • Installed in the secondary PCIe riser position of the DL360 Gen10.
    • Not required for standard SAS/SATA-only configurations.
    • Part of the DL360 Gen10 NVMe enablement hardware ecosystem.

    Additional photo(s):

    Installation point of the riser

  • HP DL 360 G10 10 Bay SAS Cable 869675-001

    HP DL 360 G10 10 Bay SAS Cable 869675-001

    This SAS cable is used specifically with the NVME backplane on the HP DL 360 G10 10 Bay server. It connects the backplane to a RAID or HBA controller and enables support for both SAS and SATA drives.

    Notes:

    • SAS data cable; not a power cable.
    • Used with the 875556-001 10SFF Premium SAS/SATA/NVMe backplane.
    • Required when using SAS/SATA drives with the Smart Array controller.
    • Does not provide NVMe connectivity by itself; NVMe drives require the additional NVMe cabling and riser hardware.
    • Part of the DL360 Gen10 10SFF Premium/NVMe storage cable set.
  • HP DL 360 G10 10 Bay NVME Backplane 875556-001

    HP DL 360 G10 10 Bay NVME Backplane 875556-001

    This is a so called “premium” backplane that adds NVME support to the HP DL 360 G10 server.

    Notes

    • Premium backplane supporting up to 10 × 2.5-inch hot-plug drives.
    • Supports SAS, SATA, and NVMe drive configurations with the required cabling and controller.
    • Requires separate power, SAS, and NVMe cables (such as 869674-001 for backplane power, plus the appropriate SAS/NVMe cable kits).
    • Intended specifically for the 10SFF Premium chassis and is not interchangeable with the 4SFF, 8SFF, or LFF backplanes.
    • Commonly found in high-performance DL360 Gen10 storage configurations.

    Additional photo(s):

     

     

  • HP DL 360 G10 10 Bay NVME Backplane Power Cable 869674-001

    HP DL 360 G10 10 Bay NVME Backplane Power Cable 869674-001

    Power cable that runs from the backplane to the motherboard for the HP DL 360 G10 10 Bay server with the NVME backplane.

    Notes:

    • Supplies power to the 10-bay (10SFF) Premium SAS/SATA/NVMe drive backplane.
    • Used in HPE ProLiant DL360 Gen10 servers configured with the 10SFF Premium/NVMe storage option.
    • Internal chassis cable that connects the system board or power distribution board to the drive backplane.
    • Required for proper operation of SAS, SATA, and NVMe drive configurations using the Premium backplane.
    • Intended specifically for the 10SFF Premium storage configuration and is not compatible with 4SFF, 8SFF, or LFF backplane assemblies.
  • HP DL 360 G10 Heatsink 873591-001

    HP DL 360 G10 Heatsink 873591-001

    High performance 1U heatsink pulled from an HP DL 360 G10 server.

    Notes

    • Passive heatsink that relies on the server’s high-airflow fan modules.
    • Compatible only with Intel Xeon Scalable (1st and 2nd Generation) processors using the LGA3647 socket.
    • Recommended for high-TDP CPU configurations where the standard heatsink (such as 873592-001) is not sufficient.
    • Not compatible with Gen9 or Gen11 HPE ProLiant servers.
    • Verify your server’s QuickSpecs or processor TDP requirements before substituting between standard and high-performance heatsinks.