AKA Mr. Cold Boot

Part Category: Storage

  • R440 8 Bay H750 PCIe SAS Cable 0TGJR4

    R440 8 Bay H750 PCIe SAS Cable 0TGJR4

    This is a SAS storage cable for the Dell PowerEdge R440. It’s compatible with RAID controllers like the H750.

    Notes:

    • Dell DP/N 0TGJR4 (TGJR4).
    • SAS cable for the Dell PowerEdge R440 8-bay SFF configuration.
    • Used to connect the 8-bay SAS/SATA backplane to supported internal storage controllers.
    • Compatible with Dell PERC controllers such as the H750.
    • Intended for the R440’s front 2.5-inch drive backplane and internal SAS storage path.
    • This is a storage-controller-to-backplane SAS cable, not a general-purpose internal SAS cable.
    • Verify the controller and backplane configuration when selecting a replacement cable.
  • R940 8 Bay SFF PCIe SAS cable 047FV4

    R940 8 Bay SFF PCIe SAS cable 047FV4

    This is the SAS storage cable for the Dell PowerEdge R940 8 Bay SFF server. It connects to the backplane and then routes to the rear of the chassis where it connects to a PCIe RAID/HBA controller.

    • Dell Part Number: 047FV4
    • Alternate Part Number: 47FV4
    • Component: Dual Mini-SAS HD storage cable
    • Server: Dell PowerEdge R940
    • Application: R940 8-bay SFF storage configuration
    • Purpose: Connects the 8-bay SFF backplane to the PERC/storage controller.
    • Connectors: Mini-SAS HD (SFF-8643) connectors
    • Configuration: Dual SAS connections, A and B
    • Cable Length: Approximately 23.5–26 inches, depending on the specific cable section/measurement.
    • Related Backplane: R940 8-SFF backplane. A parts listing specifically identifies 47FV4 as the SAS cable for the R940 8 × 2.5-inch backplane.
    • Note: This is a storage/data cable, not a power cable. The R940 8-SFF backplane is separately listed with FH049 as the signal cable and NMRWR as the power cable, while 47FV4 is the SAS connection to the PERC.

     

  • R740xd Mid Bay 02MP1D

    R740xd Mid Bay 02MP1D

    This is the mid bay for Dell PowerEdge R740xd servers. It provides the server with an additional 4 extra 3.5″ LFF drives.

    Notes:

    • Dell P/N: 02MP1D
    • Also listed as: 2MP1D
    • Type: 4-bay 3.5-inch LFF mid-tray drive cage / expansion assembly
    • Designed for the Dell PowerEdge R740xd.
    • Adds four additional 3.5-inch (LFF) drive bays in the middle of the chassis.
    • Used as part of the R740xd mid-tray storage expansion.
    • The complete expansion kit can include the drive cage/backplane and associated cables, including 03CH4K, 09NG3V, and 0YF7RN.
    • Dell part number is commonly written with the leading zero as 02MP1D, while 2MP1D is also widely used in listings

  • Cisco UCS C220 M5 internal SAS RAID controller cable

    Cisco UCS C220 M5 internal SAS RAID controller cable

    This is the SAS storage cable found in the Cisco UCS C220 M5 server. It is attached to the backplane and then routes along the right side of the server where it terminates at a RAID controller located in the mRAID riser.

    Notes:

    • Genuine Cisco OEM internal SAS cable assembly.
    • Used in the Cisco UCS C220 M5 Rack Server storage subsystem.
    • Provides the connection between the RAID controller (such as Cisco modular RAID controller / mRAID configurations or supported PCIe RAID adapters) and the internal SAS/SATA drive backplane.
    • Cable assembly uses Mini-SAS HD connectors for high-density SAS connectivity.
    • Supports SAS/SATA drive communication for internal storage configurations.
    • Designed with Cisco-specific cable length and routing to fit the C220 M5 chassis airflow layout.
    • Required for configurations using hardware RAID controllers and SAS backplanes.
    • Proper cable routing is important to avoid interference with fans and airflow paths in the 1U chassis.
    • OEM cable ensures correct connector keying, impedance, and signal integrity.
    • Commonly missing from refurbished or decommissioned servers when RAID components are removed.
    • Cable only; does not include RAID controller, riser, backplane, or drive cage unless otherwise specified.
  • HP DL 380 G10 Rear Flex Bay 871783-001

    HP DL 380 G10 Rear Flex Bay 871783-001

    This is a rear flex bay that supports 2 small form factor drives. This part was observed in an HP DL 380 G10 server.

    Notes

    • Adds two additional 2.5-inch Small Form Factor (SFF) drive bays to supported server configurations.
    • Supports SAS, SATA, and NVMe drives when paired with the appropriate backplane, controller, and cabling.
    • Designed for use with HPE ProLiant DL380 Gen10 and HPE ProLiant DL385 Gen10 servers.
    • This is a Premium HDD Cage Kit and may include the drive cage, backplane, and mounting hardware depending on the kit version. Verify the contents before purchasing, as individual components may also be sold separately.
    • NVMe functionality requires compatible system hardware, including the appropriate backplane, cables, PCIe enablement kit (if applicable), and BIOS support.
    • Commonly used to expand storage capacity or enable additional boot, cache, or data drives in existing server configurations.

    In most cases this flex bay will attach directly to port 9 on the following SAS expander as the the 380 G10 has no SAS expander built into the backplane.